Shipping advice
Sold all my fairings and shit... cannot find a damn box big enough... any advice on shipping? Box sources, packaging, freight carriers...
|
take multiple boxes and tape them together? Get some cheap 1x2 wood and make a frame and cover in cardboard?
Go buy a new fridge and use the box to ship the fairings. Couple options. |
1) Assume they will destroy it
2) Pack accordingly 3) Insurance!!! ...if possible, with a private shipping insurance firm, as UPS and FEDEX will destroy your shit, and then blame your fucking packaging, regardless of how well packed it is. 4) Pray |
Hope you got enough money for shipping from whoever you sold it to.
I recently bought new side fairings for my BMW. The box was 39"x39"x16", and to ship UPS was $140. I'm with Cutty, tape boxes together to *make* a big box. |
I shipped all my street fairings off my R6 for $73 using USPS. Luckily I had my big track bodywork box to use...
|
Make sure the boxes used are what is known as "double corrugated", or else they will blame the packing FOR SURE if anything goes bad.
|
Put "Do not stack" on it. Im sure they will but maybe those wont throw shit on it.
|
Quote:
|
Quote:
Quote:
FedEx goes by weight and dimensions... not sure about UPS... and USPS is weight only... gonna have to figure out what's cheapest, most likely USPS - however with them I have to keep the dimensions 34"x24"x24" or smaller... which should be doable... I'll just rip down some OSB into strips and reinforce the box that way... I padded the selling price so shipping was factored... I'm ending up within $10-$15 of what I wanted... good deal for everyone... |
FedEx will be the cheapest. I have shipped tons of fairings, car bumpers, and even motors. Fedex.
Hit up the local walmart even and get some boxes. |
Quote:
According to USPS' website, $107 in one box. FedEx is $108... That's if I can fit those dimensions/weight... if I go bigger or have to use more than one box, it's a toss up... With packaging and everything I figure 50lbs. |
Quote:
|
Quote:
|
Everytime I've been shipped bodywork - it's been in a big ass box with either wood or foam to keep the corners square. You can get foam pretty cheaply at a craft store - think the stuff they make flower arrangements with. Put that on the corners of the bodywork so it doesn't have a chance of going through the box.
|
Quote:
Quote:
These two. I have sold lots of stuff over the last few years, including multiple sets of body work. USPS will be the cheapest unless you have a negotiated rate with another carrier. Race body work boxes work great for shipping a whole set. UPS stores will sell "artwork" boxes which work well for side/lower fairings as long as they don't have too much of a curve to them. Get creative. Placing a large panel diagonally can help you squeeze something big into a small(er) box. Pack it well and reinforce the corners and middle. |
So.... a guy at work mentioned Greyhound... I'm like, 'the bus people?'
Apparently the bottoms of their buses are NEVER full because people traveling by bus usually don't have a lot of shit, I guess... They fill the bottoms and charge ridiculously low rates... and have ridiculous maximum dimensions (82"x47"x30"!)... I'm going to grab a couple of gaylords (the boxes) from our warehouse and build a fucking monster box to put this shit in... and save about $50 or so in shipping. BOO YA! Yeah, I said 'boo ya'... |
Most large replacement body panels sold on eBay for cars (like bumper covers, and such) are shipped by dirty dog. I should have remember to tell ya. I just hate having to drive to the bus station to get my shit, so it's not my personal fav.
|
Quote:
The Greyhound thing is pretty damn genius, though. |
Quote:
|
|
asahi thermofoil with a picture of a ..............bong?
what exactly are you shipping? :lol |
Quote:
|
All times are GMT -4. The time now is 10:01 AM. |
Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.